ANALISIS DISTRIBUSI TEGANGAN PADA SAMBUNGAN PIPA HIGH PRESSURE AKIBAT PENAMBAHAN STIFFENER MENGGUNAKAN ANSYS
DOI:
https://doi.org/10.51878/knowledge.v6i4.16888Keywords:
Tegangan Von Mises, Sambungan Flange, Stiffener Plate, Metode Elemen Hingga, ANSYSAbstract
High-pressure piping flange connections are susceptible to stress concentration due to geometric discontinuities, which may affect structural integrity. This study aims to analyze stress distribution and evaluate the effects of variations in the number and thickness of stiffener plates on Von Mises stress, stress concentration factor (SCF), and deformation in an ASME B16.5 Class 900 NPS 6 weld neck flange made of ASTM A105 steel. The study employed the finite element method using the Static Structural module in ANSYS Workbench, with an internal pressure of 15.3 MPa and a bolt pretension of 50% of the bolt yield strength. Six configurations were analyzed, consisting of one unreinforced model and five stiffener variations. The simulation results showed reductions in maximum stress of 9.31–15.87% and deformation of 22.24–25.60% compared with the unreinforced configuration. The configuration with eight 12-mm-thick stiffeners produced the lowest maximum stress of 202.47 MPa, whereas the configuration with twelve 4-mm-thick stiffeners achieved the highest reinforcement efficiency index. However, the mesh convergence study indicated that numerical stability had not been consistently achieved. Therefore, comparisons among configurations remain preliminary and require further numerical investigation.
ABSTRAK
Sambungan flange pada sistem perpipaan bertekanan tinggi rentan mengalami konsentrasi tegangan akibat diskontinuitas geometri yang dapat memengaruhi integritas struktural. Penelitian ini bertujuan menganalisis distribusi tegangan serta mengevaluasi pengaruh variasi jumlah dan ketebalan stiffener plate terhadap tegangan Von Mises, faktor konsentrasi tegangan (SCF), dan deformasi pada weld neck flange ASME B16.5 Class 900 NPS 6 berbahan ASTM A105. Penelitian menggunakan metode elemen hingga melalui ANSYS Workbench modul Static Structural dengan tekanan internal 15,3 MPa dan prategangan baut sebesar 50% tegangan luluh baut. Enam konfigurasi dianalisis, meliputi satu model tanpa penguatan dan lima variasi stiffener. Hasil simulasi menunjukkan penurunan tegangan maksimum sebesar 9,31–15,87% dan deformasi sebesar 22,24–25,60% dibandingkan konfigurasi tanpa penguatan. Konfigurasi delapan stiffener setebal 12 mm menghasilkan tegangan maksimum terendah sebesar 202,47 MPa, sedangkan konfigurasi dua belas stiffener setebal 4 mm menghasilkan indeks efisiensi penguatan tertinggi. Namun, hasil studi konvergensi mesh menunjukkan bahwa kestabilan numerik belum terpenuhi secara konsisten. Oleh karena itu, hasil perbandingan konfigurasi masih bersifat sementara dan memerlukan pengujian numerik lanjutan.
Downloads
References
American Society of Mechanical Engineers. (2017). Pipe flanges and flanged fittings: NPS ½ through NPS 24 metric/inch standard (ASME B16.5-2017). ASME.
Anuj, P., Sangeetha, N., Ashraf, S. R., Vasanthkumar, R., & Babin, T. (2022). Investigation of sealing performance with bolted flange joints with gasket using FEA method. International Journal of Vehicle Structures & Systems, 14(7), 855–859. https://doi.org/10.4273/ijvss.14.7.05
Bozkurt, M., & Nash, D. (2024). Stress linearization application of oblique nozzles with welded pad reinforcement in cylindrical pressure vessels. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 238(5), 1642–1654. https://doi.org/10.1177/09544062231187726
Bouzid, A.-H., Bouzid, S., & Benfriha, K. (2024). On the strength and tightness of ASME B16.5 and B16.47 Series A standard flanges. Journal of Pressure Vessel Technology, 146(1), 011301. https://doi.org/10.1115/1.4063890
Dai, K., Du, H., Luo, Y., Han, R., & Li, J. (2023). Stress distribution prediction of circular hollow section tube in flexible high-neck flange joints based on the hybrid machine learning model. Materials, 16(20), 6815. https://doi.org/10.3390/ma16206815
Diao, Y., He, S., Wang, Y., & Tu, L. (2024). Experimental and numerical investigations on stress concentration factors of concrete filled steel tube X-joints. Scientific Reports, 14, 11415. https://doi.org/10.1038/s41598-024-62312-8
Elkhlaidy, M., Carnicero, A., & Perera, R. (2023). Influence of flange geometric configuration and bolt stress on joint integrity during assembly using FEA. International Journal of Pressure Vessels and Piping, 202, 104912. https://doi.org/10.1016/j.ijpvp.2023.104912
Khan, K. A., & Ahmed, I. (2023). Combined loading performance analysis of gasketed bolted flange joints with emphasis on bolt scattering. Journal of Mechanical Engineering and Sciences, 17(3), 9564–9575. https://doi.org/10.15282/jmes.17.3.2023.3.0757
Kikale, S., Katkati, A., Kulkarni, A., Mache, A., Deshpande, A., & Shinde, S. (2024). Mesh convergence study on side bracket using hex-dominant and tetrahedron-dominant mesh. International Journal of Vehicle Structures & Systems, 16(6), 837–840. https://doi.org/10.4273/ijvss.16.6.05
Kuscu, K., & Singh, M. (2024). Evaluation of stresses in saddle (Q-lip) type nozzles with weaker material strength compared to the pressure vessel shell. In Proceedings of the ASME 2024 Pressure Vessels & Piping Conference (Paper No. PVP2024-122693). https://doi.org/10.1115/PVP2024-122693
Lee, C.-H., Chou, H.-W., & Huang, C.-C. (2024). Structural integrity analysis with crack propagation for reactor pressure vessel nozzles based on XFEM. International Journal of Pressure Vessels and Piping, 207, 105109. https://doi.org/10.1016/j.ijpvp.2023.105109
Lotsberg, I. (2008). Stress concentration factors at welds in pipelines and tanks subjected to internal pressure and axial force. Marine Structures, 21(2–3), 138–159. https://doi.org/10.1016/j.marstruc.2007.12.002
Mitsyuk, S. V., & Mitsyuk, D. V. (2025). Analysis of the stress–strain state of a flanged connection based on an analytical approach using the finite element method and comparison with experimental data. Strength of Materials and Theory of Structures, 115, 157–163. https://doi.org/10.32347/2410-2547.2025.115.157-163
Nelson, N. R., Siva Prasad, N., & Sekhar, A. S. (2023). Structural integrity and sealing behaviour of bolted flange joint: A state of art review. International Journal of Pressure Vessels and Piping, 204, 104975. https://doi.org/10.1016/j.ijpvp.2023.104975
Oh, C., Lee, S., & Jhung, M. J. (2022). Analytical method to estimate cross-section stress profiles for reactor vessel nozzle corners under internal pressure. Nuclear Engineering and Technology, 54(1), 401–413. https://doi.org/10.1016/j.net.2021.08.001
Sambo, M. A., Kol, G. R., & Betchewe, G. (2023). Analysis of stress concentration factors due to in-plane bending and out-of-plane bending loads on tubular TY-joints of offshore structures. Journal of Marine Science and Application, 21, 78–94. https://doi.org/10.1007/s11804-022-00303-9
Si, J., Liu, W., Zhu, L., Zhu, Y., Zhao, G., Hong, J., & Zhang, C. (2024). Experimental study on mechanic behavior of flange joint for steel tube under axial tension. Buildings, 14(8), 2282. https://doi.org/10.3390/buildings14082282
?wit, G., & Szczecina, M. (2025). Numerical study of the reinforcing pads geometry of pressure vessels. Materials, 18(10), 2318. https://doi.org/10.3390/ma18102318
Xia, Q., Ma, L., Li, G., Hu, C., Zhang, L., Xu, F., & Liu, Z. (2024). Stress concentration factors of concrete-filled double-skin tubular K-joints. Buildings, 14(5), 1363. https://doi.org/10.3390/buildings14051363
Xie, J., Lu, Z., Cao, J., Guo, Z., Kang, X., Zhang, Z., & Wang, T. (2024). Simulation and experimental study on contact pressure distribution of contact interface in single and double bolted connection structures. Journal of Low Frequency Noise, Vibration and Active Control, 43(1), 123–143. https://doi.org/10.1177/14613484231209300
Xing, W. C., Wang, J., & Wang, Y. Q. (2024). An effective model for bolted flange joints and its application in vibrations of bolted flange joint multiple-plate structures: Theory with experiment verification. Applied Mathematical Modelling, 126, 482–505. https://doi.org/10.1016/j.apm.2023.11.013
Yang, Y., Min, S., Peng, Y., Wang, H., & Chen, C. (2025). Experimental and numerical investigation on stress concentration factor of large-scale welded tubular T-joints. Ocean Engineering, 320, 120337. https://doi.org/10.1016/j.oceaneng.2025.120337
Zhang, S., De Waele, W., & Hectors, K. (2025). HFJOINT: A high-fidelity numerical modeling tool for stress concentration factor analysis of welded tubular joints. Advances in Engineering Software, 211, 104046. https://doi.org/10.1016/j.advengsoft.2025.104046
Zheng, Y., Chen, Z., Qian, H., Wang, P., & Cao, Z. (2024). A shell equilibrium modeling for stress distribution of offshore tubular joints. International Journal of Pressure Vessels and Piping, 212(Part A), 105334. https://doi.org/10.1016/j.ijpvp.2024.105334














